Pendulum Motor Control Project using Arduino

₹600-1000 INR

Inaendelea

Imechapishwa

over 3 years ago

₹600-1000 INR

Kulipwa wakati wa kufikishwa

A 3V dc motor is driven by H-bridge with Teency 3.2 and an external 4.5v battery pack. How to control length of the pendulum by driving motor clockwise or anticlockwise according to the target period. Consider the target and measured pendulum period as 16bit unsigned value in milisecond. Vary the length of pendulum between 10cm to 60cm. Raw data of period can be generated using below formula. T = 2x (pi) x sqrt(L/g), where g=9.8 m/s^2

Arduino

Electronics

Microcontroller

Electrical Engineering

C Programming

Kitambulisho cha mradi: 26970752

Kuhusu mradi

7 mapendekezo

Mradi wa mbali

Inatumika 4 yrs ago

Unatafuta kupata pesa?

Barua pepe

Faida za kutoa zabuni kwenye Freelancer

Weka bajeti yako na muda uliopangwa

Pata malipo kwa kazi yako

Eleza pendekezo lako

Ni bure kujiandikisha na kutoa zabuni kwa kazi

7 wafanyakazi huru wana zabuni kwa wastani ₹971 INR kwa kazi hii

@ZAKI102

Hi. I read your request about Pendulum Motor Control project .I can help you with this problems. I am Ph.D. student an automation and control system, I have a good experience in Arduino, Matlab and control system. I can do it You can see my previous works in my portfolio I have the honor to deal with you

₹900 INR ndani ya siku 1

5.0

(10 hakiki)

3.8

@rochaksharma7

hello sir.✋ I have just read your job description and your project is really interesting to me. The Items you raised are similar to what I have already done in practice and I think you can do it in a short time if you have a little explanation. I'm an expert having specialization in Electronic Engineering Design. ✔️ Embedded system based on Microcontroller (ATMEGA, AVR, STM8, STM32, MSP430, TMS320, PIC ...) ✔️ Python with Deep Learning, Machine Learning ✔️ Python with Data Science ✔️ A system based on development boards(Arduino, Raspberry PI, Node MCU, Bluechip, Teensy,…) ✔️ Antenna design & Analog circuit/RF communication circuit designing and simulation using Proteus, P-Spice, Tina Pro, ADS, CST, Ansys, HFSS ✔️ Bluetooth, WIFI, zigbee, LoRA ✔️ High-Speed layout using HyperLynx ✔️ PCB layout designing, providing GERBER and BOMs, 3D files using Altium, EAGLE, Kicad, EasyEDA… ✔️ Programming firmware of Microcontroller & C++ ✔️ BMS I think my many design and practical experiences can help you design your project and give you enough satisfaction. I look forward to your response. Best Regards.

₹1,000 INR ndani ya siku 7

5.0

(7 hakiki)

3.2

@mayureshmaradkar

This is a very easy problem statement..use L=power(T/2π,2)*g..This will give you the length.. control this length by using stepper/servo/encoded motor..

₹1,000 INR ndani ya siku 1

5.0

(6 hakiki)

2.4

@nikint1994

Hi, I am Embedded System professional. Having experience in Software and Hardware development. I have hands on experience in - Arduino, STM32, TI, ESP32 Firmware Development - Embedded Linux User Space Application Development - Protocols like I2C, SPI, UART, I2S - Software development in C, C++ & Python - Circuit and PCB design using DesignSpark, Orcad, Eagle, Proteus design software - AC Servo, DC Servo, Actuators control specialist I can deliver quality work in estimated time. Thank You.

₹900 INR ndani ya siku 5

0.0

(0 hakiki)

0.0

@Kshitiz101

Hello , I have more than 5 years of experience with arduino and i have solved problems like yours before , this is my first freelance bid , but i will help you complete your. project in time and also teach you the logic behind it if interested.

₹1,000 INR ndani ya siku 7