Uhandisi wa Umeme Jobs

I am routing a PCB that hosts a surface-mount SAW filter intended to clean up an RF signal in the VHF band. I want a fresh, expert pair of eyes to make sure the layout really lets the filter do its job and avoid signal integrity issues You will receive a PNG image of layout-Section SAW filter only. I need you to check trace geometry, grounding, Via strategy, impedance control, keep-out areas around the filter. Please flag any parasitic concerns—stray inductance or capacitance, via stubs, unnecessary sharp corners—or any other concerns that could compromise signal filtering performance. Input: 50 ohm CPW transmission line (bottom layer 4 and layer 3) Output: 50 ohm CPW transmission line (bottom layer 4 and layer 3) Deliverables • A single page PDF or a set of screenshots...

I need a Schneider-brand PLC programmed, tested, and fully commissioned so it communicates seamlessly with the accompanying HMI. The goal is straightforward: automate our manufacturing line’s packaging operations from end to end. Scope of work • Write the PLC logic that drives every packaging sequence, covers all required interlocks, and handles error recovery. • Configure tags and communications so real-time data flows flawlessly between the PLC and the HMI. • Build or adapt the HMI screens so operators can start, stop, and monitor the line with clear status and alarms. • Validate the solution on-site, prove that every sensor and actuator responds as intended, and fine-tune cycle times for reliable, around-the-clock production. Acceptance criteria ...

I need a senior hardware/PCB engineer with direct experience in LTE-M/NB-IoT designs to perform a thorough pre-production review of my battery-powered IoT environmental sensor board before approval is provided for prototyping. Key components MCU: Espressif ESP32-S3 Cellular module: Sequans GM02S (LTE-M / NB-IoT) + PCB antenna / Wireless: Wi-Fi + Bluetooth from ESP32-S3 Main sensor: SPEC Sensors Ethylene (C2H4) 110-65x series (analog output) + additional digital environmental sensors (I2C/SPI) Power: Single-cell LiPo battery, charging via dedicated charger IC, ultra-low power sleep modes Design files: Altium Designer project + Gerbers Target markets & certification Primary: Australia (RCM mandatory) Future: Europe (CE RED), North America (FCC/IC), global roaming Scope of work Full ...

I run the engineering operations at FreezeM, where we design and build early-life-stage Black Soldier Fly production lines. Our site is based in Germany Baruth. It runs a mix of fully automated and semi-automatic units, and Both equally need ongoing care. I am looking for a dependable maintenance partner who can cover Both equally Preventive maintenance and Corrective maintenance on a scheduled and on-call basis. Most of the attention revolves around: • Mechanical failures, Electrical issues, and occasional Software glitches on the semi-automatic stations. • Routine servicing of actuators, conveyors, vision systems, arduino/rasppberpi-controlled modules, sensors. Typical scope – Plan and execute preventive checks, lubrication, calibration, and firmware updates without...

I need existing Mechanical and Electrical (M&E) drawings updated. The project involves: - Updating plumbing systems in mechanical systems - Revising power distribution in electrical systems Ideal skills and experience: - Proficiency in M&E systems design and modification - Expertise in plumbing and electrical power distribution - Experience with CAD software for drawing updates - Attention to detail and accuracy in engineering drawings I've attached 25mb of drawings but there are more.

I need a clear, production-ready schematic for an in-ear wireless earbud PCB. I will handle the final board layout and manufacturing myself, so what I am really after is a solid electronic blueprint that I can drop straight into the CAD stage. At this point I’m flexible about the EDA package—Altium Designer, Eagle, KiCad or any comparable tool is fine as long as the files are exportable to standard formats (PDF for the schematic, native design files, and a searchable BOM). We can fine-tune feature details such as Bluetooth, noise cancellation or touch sensing once we start; the schematic just needs to leave room for whichever combination we lock in. Deliverables • Complete, well-labeled schematic of the earbud PCB • BOM with footprints, part numbers and supplier...

I need a comprehensive MV LV protection and coordination study to ensure safety compliance. The focus will be on transformers and switchgear, adhering to IEC standards. Key Requirements: - Detailed analysis of protection settings - Coordination study for fault conditions - Compliance with IEC standards - Comprehensive report with recommendations Ideal Skills: - Expertise in MV LV systems - Strong knowledge of IEC standards - Experience with transformers and switchgear - Proficient in protection coordination studies - Ability to deliver clear, detailed reports

This is a two-device RF relay system that extends the communication range between a car key and the car. I am looking for only UK developers

I need a freelancer to build a complete MATLAB/Simulink simulation for a bio-inspired autonomous underwater vehicle (AUV) that uses undulating fin locomotion. The simulation should model the nonlinear vehicle dynamics, generate fin-based thrust, and test an advanced control architecture. What the simulation must include 1. Nonlinear 3-DOF AUV Dynamic Model • Surge, sway, yaw, and heading • Added mass, quadratic drag, cross-coupling terms • Environmental disturbances (currents, turbulence, noise) 2. Fin Waveform Generator • Traveling sinusoidal fin motion • Adjustable amplitude, frequency, and phase • Mapping from fin motion → thrust, lateral force, and yaw moment 3. Control System Implementation • Fractional Sliding Mode Controller (FSMC) ...

I’m looking for a freelancer with experience in Python, PyWake, and wind energy modeling to help me build a set of simulation scripts and a written technical report. The simulations will analyze a real existing wind farm using data from Global Wind Atlas or Sea Impact. You will use PyWake () and optionally the included PyWake Workspace to run several analyses and generate meaningful visual outputs. Deliverables 1. Wind Farm Layout Plot 2. Wake Visualization 3. AEP (Annual Energy Production) Simulation 4. Wind Direction Analysis 5. Wake Loss Comparison Technical Report Requirements: A well-structured report (PDF or Word, 9-12 pages) explaining: The wind farm used and its data sources All simulation methods Code explanations Plots + tables Interpretation of AEP, wake losses, and dir...

We are seeking an experienced water treatment process engineer or consultant to support the design of a compact modular potable water treatment system for commercial development in Lagos, Nigeria. The treatment philosophy includes: - Venturi aeration for iron/manganese oxidation - Catalytic media filtration - Adsorptive polishing (activated carbon/organic removal) - UV disinfection - RO + remineralization for premium applications The consultant will be responsible for: 1. Reviewing and validating our design philosophy and treatment flow. 2. Assisting with P&ID/process schematic development. 3. Confirming appropriate component sizing (media vessels, pumps, flow rates, UV capacity, RO configuration). 4. Recommending material specifications and modular layout options. We pr...

I need an engineer to assess my mobile home for fire damage. The assessment should cover: - Structural integrity - Electrical systems A written report is required, which should include: - Detailed assessment results - Recommendations for repair or improvement Ideal skills and experience: - Engineering background - Experience with mobile homes - Knowledge of fire damage assessment - Strong report writing skills

Project Overview We are developing a next-generation vessel sealing generator similar to Valleylab LS10 / Voyant RF sealing systems. The device is a medical-grade, high-frequency RF surgical generator operating around 400 kHz, delivering controlled energy to surgical instruments for vessel sealing. We are looking for an experienced PCB Design Engineer with medical device background and strong familiarity with: IEC 60601-1 safety requirements (creepage, clearance, MOPP, isolation) IEC 60601-1-2 EMC design practices High-frequency power electronics (200–500 kHz) Full-bridge power stages, resonant tanks, HF isolation transformers Mixed-signal PCB layout (DSP, MCU, analog sensing circuits) This is not a basic PCB job; we need someone comfortable designing medical-grade, safe, iso...

Necesito ayuda para editar un plano eléctrico en AutoCAD. Requisitos: - Agregar detalles según las instrucciones proporcionadas. - Incluir salidas de voz y datos (internet): - Necesito las ubicaciones exactas y la cantidad de salidas. Habilidades Ideales: - Dominio de AutoCAD. - Experiencia con planos eléctricos. - Atención al detalle.

I need an experienced electrician who can diagnose and repair several issues throughout my property—both inside and outside. The scope includes flickering or non-working lighting fixtures, dead or overheating outlets and switches, and a circuit breaker that trips without warning. To complete the job you’ll need to bring the right test equipment (multimeter, voltage tester, breaker finder) and carry any common replacement parts so work can be finished in a single visit whenever possible. Deliverables I’ll sign off on: • Lighting fixtures restored to stable operation, with safe wiring and proper grounding • All affected outlets and switches replaced or repaired, verified for correct polarity and load handling • Circuit breaker fault identified and res...

I need someone with direct OptiFDTD (Optiwave) experience to rebuild a photonic-crystal biosensor geometry from a published paper. Scope of this initial milestone (partial test): – Recreate lattice geometry (hole radius, period, defect region) – Assign refractive index values to substrate, waveguide and analyte regions – Apply PML boundaries and monitors using a provided template – No simulation runs, no CSV export Deliverable: – A clean OptiFDTD project file (.fdt) that opens without errors This is a test milestone before awarding the full project. To qualify, reply with: Version of OptiFDTD you have used Screenshot of ANY previous OptiFDTD geometry or monitor layout (mandatory) Estimated time to complete partial geometry setup Do NOT apply if you only ...

I have already built a two-terminal HVDC transmission model in MATLAB/Simulink that incorporates power-flow control and has demonstrated a 20 % overall efficiency gain in preliminary tests. My next objective is to push that figure higher by targeting energy-loss reduction while validating the model’s behaviour under grid-interconnection scenarios. Here is what I have in place: • A functioning Simulink schematic of the converter stations, DC line, and AC grids • Basic power-flow control logic that balances the two terminals • Data from the first round of simulations confirming the current gain Where I need your help is in refining the model so that every avoidable watt stays in the system. Specifically, I want to: • Identify and quantify dominant loss paths ...

I'm seeking an expert in electrical engineering, specifically in power systems, for design and analysis consultancy. The focus will be on commercial power distribution. Additional services include Project Engineering services. Ideal Skills and Experience: - Advanced knowledge in power systems, especially commercial power distribution. - Proven track record in design and analysis. - Strong analytical and problem-solving skills. - Relevant certifications in electrical engineering. - Experience in leading projects from end to end and generic project management. Please provide a portfolio showcasing similar projects and your approach to power systems design and analysis.

I’m bringing an LED flashlight to market that must deliver premium performance while keeping component and assembly costs razor-thin from day one. The product will be used outdoors at night, so reliable brightness and a notably long battery life are non-negotiable. Water resistance or tactical extras are welcome if they don’t inflate the bill of materials, yet the headline goal is clear: maximise runtime and durability without letting unit cost creep upward. What I expect from you • A complete electromechanical design optimised for Design-for-Manufacture (DFM) and high-volume assembly • A costed BOM showing part numbers, unit prices and target margins • Schematic, PCB layout (Altium or equivalent), mechanical enclosure files (SolidWorks, Fusion 360 or simila...

I already have a general write-up on how a flashlight converts chemical energy from its batteries into light, but the section about the lamp itself still needs real depth. I’ve chosen to focus on the LED option because the flashlight will be used mainly for outdoor activities such as camping and night trekking, so durability, brightness and energy efficiency are critical. What I need from you is a clear, technically accurate explanation of the LED component inside a modern flashlight. That includes how the diode actually produces light, the role of the reflector and lens in shaping the beam, typical current and voltage ranges for common AA/AAA builds, heat management considerations, lumen output versus runtime, and any special coatings or materials that improve outdoor performance...

I already have a general write-up on how a flashlight converts chemical energy from its batteries into light, but the section about the lamp itself still needs real depth. I’ve chosen to focus on the LED option because the flashlight will be used mainly for outdoor activities such as camping and night trekking, so durability, brightness and energy efficiency are critical. What I need from you is a clear, technically accurate explanation of the LED component inside a modern flashlight. That includes how the diode actually produces light, the role of the reflector and lens in shaping the beam, typical current and voltage ranges for common AA/AAA builds, heat management considerations, lumen output versus runtime, and any special coatings or materials that improve outdoor performance...

I’m taking Belflör Bloom from concept drawings to a fully working wrist-mounted prototype and need end-to-end help—hardware, firmware, and interface all in one coordinated build. Core function The first release has a single job: effortless music control. Play, pause, skip, and volume adjustments must work through three parallel input methods—capacitive touchscreen gestures, voice commands, and tactile side buttons. No health tracking or notification features are required at this stage, but the architecture should leave room for them later. What the work involves • Hardware: board layout, component selection (BLE-enabled SoC, microphone array or MEMS mic, haptic motor driver, battery management, low-profile tactile switches, 1.4-1.6" touchscreen), encl...

I’m putting together a practical action plan to lift Aceh’s economy by strengthening its agriculture sector, and I want to start with crop production—the heart of most rural livelihoods here. I need a knowledgeable partner who can translate proven agronomic practices into steps that fit our local soil conditions, climate patterns, and market realities. Here’s what I already know: the biggest lever for economic growth in my region is agriculture, and crop production in particular. What I still need is clarity on the most impactful intervention—whether that ends up being higher-yield seed varieties, smarter pest-management protocols, modern irrigation layouts, or a blend of these. Your job is to analyse the current situation, prioritise opportunities, and deliv...

I need an AutoCAD drawing for an electrical project, specifically focusing on materials. The drawing should include channels. Ideal skills and experience: - Proficiency in AutoCAD - Experience with electrical drawings - Attention to detail - Knowledge of electrical materials, especially channels

. Project Overview The Smart Blind Stick is designed to assist visually impaired people by detecting obstacles and providing GPS-based navigation. It uses sensors to detect obstacles and vibrations or audio alerts to warn the user. Ideal for: • Visually impaired individuals • Accessibility devices • Assistive technology project ________________________________________

I'm looking for a skilled COMSOL user to help validate a hypothesis related to thermal effects. The main focus will be on thermal phenomena. Key Requirements: - Expertise in COMSOL, specifically in thermal simulations. - Ability to accurately validate hypotheses. - Experience with setting up and interpreting thermal effect simulations. Ideal Skills: - Strong background in thermal dynamics. - Proficiency in using COMSOL Multiphysics. - Analytical skills to interpret simulation results. Please provide relevant experience and approach in your bids.

I have five DVD recorders, each with its own internal tuner, yet none of them will currently lock on to the usual UK Freeview channels (BBC, ITV, Channel 4, Channel 5, and the rest). What I need now is clear, practical guidance that will get every unit reliably receiving those services again. Here’s the situation so far • All five recorders report a tuner, but they either return “no signal” or pick up only a handful of shopping channels. • I’m uncertain whether all machines are sharing the same aerial feed or if each has ended up on its own run of coax. • I’m open to adding an external solution—splitter, signal amplifier, standalone Freeview box, whatever makes the most sense—but I’d like your recommendation before I buy...

I want a well-researched, reader-friendly comparison between the Indian Railways WAP-7 electric locomotive and the WDP-4D diesel twin-cab. The piece should open with a clear overview of why these two machines matter, then dive into hard numbers—horse-power (6 350 HP vs 4 500 HP), top speed, tractive effort, axle load, and acceleration. From there, set the locomotives side-by-side on typical operational contexts: premium electrified corridors for the WAP-7, non-electrified long-distance routes for the WDP-4D, highlighting real-world train examples where possible. Beyond raw performance, include: • Technical specifications: prime mover / traction motor details, gear ratios, braking systems, and control electronics. • Route suitability and turnaround logistics, noting how ...

I’m reviving the classic living-room radiogram as the Eco Radiogram—a single piece that balances elegant, sustainable construction with cutting-edge convenience. Modern technology is the priority, so every decision must support a seamless, up-to-date user experience while respecting ecological principles. Core tech requirements • Bluetooth connectivity for effortless wireless audio • Voice recognition that works naturally in a typical home environment • Smart-home integration (Alexa, Google Home, HomeKit) for hands-free control Interaction All primary functions will be accessed through a capacitive touchscreen set flush into the timber front panel. It has to feel intuitive, quick, and visually in tune with the warm aesthetic of reclaimed or sustainabl...

I'm seeking an experienced PCB designer to create, build, and test a custom rectangular PCB for a wearable light display device. The device will use a Xiao ESP32-C3. Key components to integrate: - round LIPO Batery 3,7v 500mah 38 diameter. - Press button sensor TPP 223 - mosfet - Setup to conect xiao ESPC23c3 - resistencias 10k ohm - 100m ohm Control methods: - Manual via button - App-based (WiFi enabled) Ideal skills and experience: - PCB design and fabrication - Experience with ESP32 and wearable tech - Mobile app integration for control - Testing and troubleshooting electronics

Looking for an Electrical Engineer – Simple Lighting & Wiring Design I need an electrical engineer to prepare basic drawings and calculations for a small project. The shed size is 25 m × 35 m × 8.5 m and it is relocatable. Work Needed (Very Simple): Lighting layout / RCP – Show positions of lights – Show wiring loops – Show DB location Single Line Diagram (SLD) – Simple SLD with MCB ratings and cable sizes. DB Schedule – Small table showing circuits and MCB ratings. Earthing layout – Just show earth pit and connections. Basic Calculations – Load calculation – Lux calculation (700 lux) – Cable sizing – Earthing conductor size Small design report – 4–6 pages only

I'm seeking assistance for functional testing on my Depression Support Doll prototype. The invention is currently at the research (IDEA) development stage, and I need to ensure its performance meets the required standards. Key requirements: - Conduct thorough performance testing - Identify any potential issues or weaknesses - Provide detailed feedback and recommendations Ideal skills and experience: - Expertise in testing electronic devices, especially radios - Strong analytical skills - Experience in providing actionable feedback for prototypes Looking forward to collaborating with a skilled professional to perfect my invention.

I need a detailed AutoCAD design for a new warehouse. I have a project requires: - Floor plans - Electrical and data drops The designs should be at a detailed architectural level. Ideal candidates will have: - Proficiency in AutoCAD - Experience with warehouse design - Strong understanding of electrical and data layouts Please provide samples of previous work. Looking forward to your bids!

I have an on going project with STM32U5G9ZJT6Q on one of my Host board. The Host PCBA is connected to an external display via parallel interface. Currently its working with a different display but we would like to update the GUI compatible with a new LCD that we purchased (CH430WV11A-CTB). The milestone descriptions is as follows: 1. Update the Host firmware to support and integrate the new Chinese LCD CH430WV11A-CTB (). All the new assets of the UI have been adjusted already according to the new display. 2. Add additional new screens from the latest link provided by us and use the latest assets for the update. 3. Follow the “CO.8 - STM Board Set 1st Firmware Review_08082025” document for firmware updates and fixes to the GUI. 4. Enable Haptic motor function when scrol...

Somos KAMEFU, empresa peruana dedicada al mundo recreativo, con un fuerte sentido de innovación y enfoque en experiencias presenciales memorables. Estamos buscando un/a ingeniero/a electrónico/a con experiencia en diseño de PCB para desarrollar la electrónica de un nuevo juego físico de carreras con hasta 20 jugadores simultáneos. El proyecto combina: Módulos electromecánicos (sensores y motores por carril). Una unidad de control central robusta para uso intensivo. Integración con pantallas (posiciones y nombres de jugadores). El énfasis principal de esta convocatoria está en el diseño profesional de la placa PCB y la selección de componentes adecuados para un entorno real de trabajo (variacione...

My solar business is growing quickly, and I need experienced crews who can take a residential project from roof-mount to meter turn-on without hand-holding. Your core focus will be installing brand-new photovoltaic systems on single-family homes: setting racking, mounting panels, running conduit, pulling wire, landing everything in the inverter and combiner, and finishing with code-compliant commissioning. You’ll be working only on fresh installs—no maintenance or retrofits. Jobs are clustered within the same neighborhoods, so efficiency and neat workmanship matter. If you’re an electrician, the work centers on the AC hand-off: final terminations into the main service panel, labeling, and ensuring the install passes local inspection the first time. To keep things smoo...

I need a PCB layout produced and delivered in a compatible Circuit Studio format. The board will act as a four-slot bifurcation breakout for a PCIe x16 edge connector. Key parameters you should work to: • Form-factor: custom 100 mm × 80 mm, two-layer copper. • Material: standard FR-4. • Both boards must support full lane bifurcation from a single x16 input to four downstream connectors and keep differential-pair routing length-matched and impedance-controlled. Two GPU spaced PCIE16x connectors on one side, two GPU spaced PCIE16x connectors on one other. see sketch. PCB footprint MUST be minimized for airflow reasons( board may be perpendicular to colling airflow.) add PCIE edge connector(90º optional, do not include in V1.0). board is "reversed breako...

I need detailed electrical load calculations for a commercial building. The focus is on a dual-port EV charger with the following specifications: - 80 amps - 19.8 kW Ideal Skills and Experience: - Electrical engineering background - Experience with commercial load calculations - Familiarity with EV charging systems

Location: Visakhapatnam Job Type: Full-Time About the Program The SHARD Program is an innovative, school-focused initiative designed to bring hands-on robotics, AI, and STEM learning to students from Grades 3 to 10. Our goal is to spark curiosity, build practical skills, and prepare students for the future through experiential education, real-world problem solving, and cutting-edge technology exposure. We are expanding rapidly and are looking for passionate, energetic trainers who can inspire young minds. Role Overview The Robotics & AI Trainer will be responsible for delivering robotics, STEM, and AI-based sessions to school students, conducting workshops, supporting project demonstrations, and ensuring smooth implementation of the SHARD curriculum across partner schools. Key Re...

I need an experienced hardware engineer to design a robust, automotive-grade PCB built around an STM32H7 microcontroller. This board will function as a drivetrain/traction-control module and must meet high reliability, EMI, and durability standards for use inside a vehicle environment. The enclosure and connector/header layout are already defined and must be followed for mechanical fit. No schematics exist yet — this is a complete design from scratch. --- Required Features Core MCU STM32H7 series with 2× native CAN FD Support for 3rd CAN FD bus via external SPI CAN FD controller Analog switch to optionally bridge the two native CAN FD buses (programmable link/isolated mode) Connectivity ESP32 module for wireless support STM32 ↔ ESP32 communication (UART/SPI) USB p...

We are a USA-based audio company with over 50 years of industry experience, seeking a highly skilled Digital Engineer to join our team full-time. This is a long-term position (years, not months) supporting ongoing projects in collaboration with our local engineers in Canada and the USA. The ideal candidate will work North American hours (flexible if needed) and possess expertise in embedded systems development. Mandatory Skills: 1. Proficiency in MCUXpresso IDE (FreeRTOS) for NXP embedded platforms. 2. Experience with Atmel Studio for Atmel AVR programming (C or machine language). 3. Familiarity with JTAG, USB, PHY, MIPI, I2C, and SPI protocols. Nice-to-Have Skills: 1. Knowledge of Arduino programming. 2. Experience with legacy Microchip programming for product support. 3. Passion for h...

I am seeking an electrical engineer to visit 1, Rue de la Burelle, 45800 Saint Jean de Braye, France, to perform testing on a diesel generator. The task involves conducting specific tests to ensure the generator is functioning properly and meets required standards. Additionally, clear pictures of the generator and its nameplate should be taken for documentation purposes. This is an on-site job that should be completed within one day.

I have an early-stage prototype of our in-house AI voice assistant and a clear spreadsheet listing every connector, interface and mechanical constraint we must respect. What I now need is a production-ready custom PCB that folds all of those pieces into a compact, reliable board dedicated to a voice-first device. Core features the board must accommodate include voice recognition processing, high-quality audio playback, robust wireless connectivity (Wi-Fi and Bluetooth), a beam-forming microphone array, a small display ribbon connector, and a camera interface. Size, heat dissipation and low-noise routing around the microphones are especially important, so experience with mixed-signal layout and RF coexistence is a plus. The schematic is partially drafted, component selections are frozen, ...

I already have a complete single-line diagram, breaker model numbers, cable lengths, and load data; now I need the full Selectivity (coordination) Study carried out in Schneider’s EcoDial. The heart of the job is precise circuit-breaker selection and sizing, so every calculation needs to be traceable back to the actual catalogue numbers I supplied. Once the study is complete, I expect two concrete deliverables: • The native EcoDial project file, fully updated with all settings and comments. • A professionally formatted PDF report that walks through breaker choices, protection settings, load evaluation, cable-length verification, and any recommendations or notes that arise from the analysis. Please use EcoDial’s built-in reporting and your own engineering commenta...

panel commissioning , training

I need specialized engineering services to ensure my auto repair shop drawings are permit-ready for Texas. The drawings exist but require expert plans from licensed professionals. I need a Civil , Structual, MEP, Fire Protection and geotechnical Scope of work - Prepare permit-ready civil engineering plans. - Develop structural engineering plans based on existing drawings. - Create MEP, fire protection, environmental, geotechnical, and EV engineering plans. Additional information I will verify licenses of the engineers. The drawings are existing and need professional plans made for permits. Ideal Candidates - Licensed civil, structural, MEP, fire protection, environmental, geotechnical, and EV engineer. - Experience with permit-ready plans for Texas. - Familiarity with auto repair shop r...

Hello, We are looking for an experienced trainer to deliver a short-term training project on "Siemens PLC Training". Responsibilities: - Conduct focused training sessions on Siemens PLC Training - Create or adapt training material as required - Provide hands-on lab guidance (if applicable) Requirements: - Proven experience in Siemens PLC Training - Prior corporate training experience preferred - Ability to deliver training effectively within a short-term timeline To Apply, Please Share: - Updated CV / Profile - Course contents (TOC) - Daily / Hourly commercial rates - Lab availability & charges (if applicable) - Your availability schedule Looking forward to collaborating with the right expert. Best regards, Anjali Koenig Solutions

Hello, We are looking for an experienced trainer to deliver a short-term training project on "PLC, Telemetry, and SCADA Systems: Control and Automation Essentials". Responsibilities: - Conduct focused training sessions on PLC, Telemetry, and SCADA Systems: Control and Automation Essentials - Create or adapt training material as required - Provide hands-on lab guidance (if applicable) Requirements: - Proven experience in PLC, Telemetry, and SCADA Systems: Control and Automation Essentials - Prior corporate training experience preferred - Ability to deliver training effectively within a short-term timeline To Apply, Please Share: - Updated CV / Profile - Course contents (TOC) - Daily / Hourly commercial rates - Lab availability & charges (if applicable) - Your availability ...

I need a compact, single-board solution that combines a Raspberry Pi Zero 2 W, its camera module, an ADXL accelerometer, and a TP4056 charging circuit able to supply a steady 2 A for display unit. The board’s primary job is continuous video recording/streaming while remaining fully portable, so the power stage must keep the Pi and camera running for at least six hours on a 3 00 mAh Li-ion pack (or any cell that realistically meets that runtime). Layout considerations • Keep the Pi’s CSI ribbon connector, mini-HDMI, USB OTG, micro-SD slot and 40-pin header accessible. • Route the ADXL close to the board edge to minimise vibration damping. • Provide status LEDs for charge, power-good and recording. • Respect the TP4056 thermal requirements and add pro...

Description: Looking for an expert in BLDC motor and propeller design to develop five custom drone motors from scratch — including stator and rotor design, electromagnetic + thermal simulations, and matching propeller design for each. Tasks: 3D design of 5 BLDC motors (different power classes) EM simulations (torque-speed curve, back EMF, efficiency map) Thermal, stress, and vibration analysis Propeller design optimized for each motor CFD-based performance and thrust analysis Deliverables: CAD models (motor + propeller) FEA/CFD simulation reports Torque-speed & efficiency plots Material and winding specifications Preferred tools: ANSYS Maxwell / Motor-CAD / SolidWorks / Fluent / MATLAB Goal: To create optimized, high-efficiency drone motor-propeller systems ready for...