Arduino Code to activate RGB LEDs

$12-30 SGD

Imefungwa

Imechapishwa

about 5 years ago

$12-30 SGD

Kulipwa wakati wa kufikishwa

I want an Arduino with a sensor to drive some RGB LEDs. I have done a similar code before but I need more configurability. See requirement below... 1. Must run on ATTiny85. 2. Must be able to set number of RGB. 3. Must be able to choose RGB effects from "[login to view URL]" 4. Only ONE effect needs to be displayed. 5. RGB effects activated from a Microphone or Motion sensor. 6. Must be able to set Microphone or Motion sensor trigger threshold. 7. Must be able to set number of trigger for sensor. Please see attached for example of what I have done before.

Arduino

Microcontroller

Programming

Kitambulisho cha mradi: 18954672

Kuhusu mradi

10 mapendekezo

Mradi wa mbali

Inatumika 5 yrs ago

Unatafuta kupata pesa?

Barua pepe

Faida za kutoa zabuni kwenye Freelancer

Weka bajeti yako na muda uliopangwa

Pata malipo kwa kazi yako

Eleza pendekezo lako

Ni bure kujiandikisha na kutoa zabuni kwa kazi

10 wafanyakazi huru wana zabuni kwa wastani $33 SGD kwa kazi hii

@soltracker

yes buddy, A super simple project to be done, u will get the best work accompanied with brotherhood,,,,,,,,,,,,,

$30 SGD ndani ya siku 1

4.7

(20 hakiki)

3.8

@imad2010j

hi sir I was so excited when i read ATTINY85, I want to take this work, I already work with the ATTINY85 and W2812 LEDs. I am an expert in automation and I study in a faculty of electronics.

$27 SGD ndani ya siku 10

5.0

(8 hakiki)

3.4

@kahan1994

Hi, I am kahan. I am embedded developer and have much experienced in hardware and software side. Waiting for further discussion. Thank you.

$46 SGD ndani ya siku 3

5.0

(6 hakiki)

3.0

@mohamed13askar

Hi, I could help with this project, I just would like to know if you want the microphone to be as a noise detection device ? Regards, Mohamed

$52 SGD ndani ya siku 1

5.0

(2 hakiki)

2.7

@AmrOkasha975

I can write the code to drive the leds on Attiny85 as I have good experience with AVRs and arduinos

$26 SGD ndani ya siku 2

5.0

(1 hakiki)

0.6

@MeeraPatel5

I am new to this Freelancer site. However I have work experience of 4 year. I have worked on Arduino, and controllers of STM, NXP and Nordic semiconductor. So, I have great knowledge about programming and debugging code for controllers on Keil IDE or on Arduino. I have also worked on motion Sensors (Piezo, Gyro, Accelerometer, Magnetometer), IR sensors and designed many custom boards for a startup in India, Gujarat. I have just worked on a project that included RGBs. So, I know about the data sheets, current requirements, their different effects, calculations of resistor values of different RGBs and their manufacturers.

$27 SGD ndani ya siku 2

0.0

(0 hakiki)

0.0

@chipmetrix

I will provide you all the firmware as per required flow I will provide bug free firmware . i will assist in testing . i will support till, end of project

$27 SGD ndani ya siku 2

0.0

(0 hakiki)

0.0

@fpgaedge

hi. Ii just wanted to help you. I love doing Arduino projects specially rgb led. because the combination of the lights is really cool and amazing. I've done a lot of projects using rgb led. I'm sure i can help you a lot. hope you choose me. :). if you want to start now, just send me a message. :) . thanks. I'm just an electronics engineer who is passionate in doing things related to Arduino programming. :) thanks

$30 SGD ndani ya siku 1