Find Jobs
Hire Freelancers

Programming iMX8 GPIO

$30-250 USD

Imefungwa
Imechapishwa over 2 years ago

$30-250 USD

Kulipwa wakati wa kufikishwa
We are looking for code to generate the signals (as seen in signal.jpg-attached) on GPIO pins of iMX8 microprocessor. The clock frequency is 25Mhz With a delay starting at 7 Nano Seconds and going up to 625 Nano Seconds, with 40 clock pulses finishing within 2.38micro seconds. In the diagram attached, ts width= 625ns, ts1-s2 delay=150ns, ts-p delay=42.5ns More details will be shared with whomever is chosen. We need a quick turn around, output needed in 1week maximum. Coding language has to be C/C++ and OS on MPU Linux
Kitambulisho cha mradi: 31886861

Kuhusu mradi

6 mapendekezo
Mradi wa mbali
Inatumika 2 yrs ago

Unatafuta kupata pesa?

Faida za kutoa zabuni kwenye Freelancer

Weka bajeti yako na muda uliopangwa
Pata malipo kwa kazi yako
Eleza pendekezo lako
Ni bure kujiandikisha na kutoa zabuni kwa kazi
6 wafanyakazi huru wana zabuni kwa wastani $389 USD kwa kazi hii
Picha ya Mtumiaji
I'm an experienced Linux system administrator with more than 5 years of experience in enterprise environments working mainly with RHEL (5,6 and 7) and SLES (10,11 and 12). I'm working with confidence with the following technologies: NFS (kerberized and plain), SAMBA (standalone only), APACHE, Linux Clusters (RHEL 7/ SLES 11 and SLES12), iSCSI Target (standalone and clusterized) and Initiator, SELINUX, Firewalld/SuSEFirewall2/IPTABLES, Advanced Networking (teaming, bonding, static routes), MySQL/MariaDB administration (without DB design) ,GlusterFS, oVirt ,etc
$200 USD ndani ya siku 7
4.9 (70 hakiki)
6.0
6.0
Picha ya Mtumiaji
Good morning, I quote about 2.5 days work so we can exchange and adjust the solution. In principle an ARM processor board such as beagleboard, raspberry or similar will be fit for this work, along with certainly C/C++ program and XML file for parameters so the output logic can be changed and tuned according to your needs by yourself without requiring modifying the main program. We can see the details about this device later on the chat. Regards, Jean-François Simon *** Good day, Chrysalide Engineering is an electrotechnic consultant and engineering company founded after 15 years experience in the domain. I propose consultant work, calculation notes, design specifications, engineering documents, service. 1 Activities — Electrotechnic et automation — Instrumentation, distribution, conversion — Electronics — Embedded — Software 2 Engineering capabilities — Front-end engineering — Project management — Preliminary studies and design — Wiring diagrams — Engineering documentation — Support for commissioning — On-site training 3 Typical supply — Wiring diagrams — Design specification — Source code — Manuals — Layout drawings Regards, Jean-François Simon
$1,300 USD ndani ya siku 21
5.0 (1 hakiki)
4.1
4.1
Picha ya Mtumiaji
PHD IN SOFTWARE DEVELOPMENT AND ARCHITECTURE. EXPERT IN ABOVE NAMED SKILLS. HELLO DEAR CLIENT! Thank you for sharing your project details, I have read and understood them. Am interested in your project and I would like to take part in making it a success. Please consider me. I will work to your satisfaction by providing the best quality and communicate throughout the project. Please send me a message we discuss more about your project. CHEERS.
$200 USD ndani ya siku 7
2.6 (9 hakiki)
4.3
4.3
Picha ya Mtumiaji
Hello, I have 10+ years of Embedded product design with multiple domains like a consumer, industrial, automotive, IOT and wearable product. -Hardware architecture design using MCU, controller, and FPGA, as well as low power battery, operated device -Experience in all phases of product development from prototyping to mass production -Experience in Schematic and high-speed PCB layout board design with multilayer PCB design, Blind & Buried Vias in HDI Design. -Expertise in hardware testing and troubleshooting/root cause -Working experience on power management system design with Buck-boost, Battery charger, and fuel gauge, USB3.0 Ctype and PD charging, POE and etc -Expertise in design and simulation of analog circuits -Experience in Microprocessor and microcontrollers like NXP, ST, Microchip, Marwell, Qualcomm, MediaTek, TI, Renesas, and Atmel -Exposure in mechanical design review -Expertise in wireless SOC with Bluetooth, WIFI, 4G, Lora, Zigbee from NXP, Nordic, Ublox, Qualcomm, Cypress, Broadcomm, TI, ESP, Silabs, Microchip -Experience in wire interface USB2/3, SPI, I2C, UART, HDMI, Ethernet, SDIO, MIPI-CSI/DSI, CAN, Modbus, RS232, RS485 -Expertise in solving problems of EMI/EMC -EMI / EMC compliance testing and product certification like CE/FCC/UL and etc Also, We have a team for software development, firmware development as well as CAD design. we will define milestone and adjust amount after discussion Let me know if you need help from me. Thanks. --Alpesh
$250 USD ndani ya siku 7
5.0 (2 hakiki)
2.3
2.3
Picha ya Mtumiaji
I have reviewed your bid request and I am very interested in your project. I was trained overseas and have an extensive customer service record so contact me so we can discuss further or begin.
$183 USD ndani ya siku 8
4.5 (1 hakiki)
2.0
2.0
Picha ya Mtumiaji
We are a Product Design and Development company with expertise in embedded systems and robotics . We provide Services such as Embedded Firmware Development for Controllers and Processors , Embedded Hardware Design and PCB Design . Kindly Share your requirement in detail to we could assist you with the same.
$200 USD ndani ya siku 7
5.0 (1 hakiki)
1.4
1.4

Kuhusu mteja

Bedera ya INDIA
Ahmedabad, India
0.0
0
Njia ya malipo imethibitishwa
Mwanachama tangu Des 3, 2015

Uthibitishaji wa Mteja

Asante! Tumekutumia kiungo cha kudai mkopo wako bila malipo kwa barua pepe.
Hitilafu fulani imetokea wakati wa kutuma barua pepe yako. Tafadhali jaribu tena.
Watumiaji Waliosajiliwa Jumla ya Kazi Zilizochapishwa
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Onyesho la kukagua linapakia
Ruhusa imetolewa kwa Uwekaji wa Kijiografia.
Muda wako wa kuingia umeisha na umetoka nje. Tafadhali ingia tena.