ARM SOC firmware Engineer (HT5019 SoC)

How are you? Like you see in my profile and portfolios, I have rich experience in C/C++, C#, and Python programming as well as microcontrollers. Especially, I completed many embedded firmware projects for such features. I would like to discuss with you and get more detail requirements. Please give me your details, then I will provide best solution for you. Thanks

Hi, I am a post graduate power electronics engineer and having very good experience in product design and development. I am excellent in embedded design & programming using pic, dspic controllers and MATLAB codding for Power projects, Boot loaders, Bluetooth & GPS designs, CAN communication, EEprom. UART , RF circuits ,Protocols for networking, wi-Fi routers,OBD diagnosis with CAN bus protocols, Electrical vehicles and AC drives, stepper motor controls. I designed sine wave inverters for standalone and grid tie Inverters. I designed projects like Off line UPS up to 3 KVA, 5kW motor controller for electrical vehicles ,synchronous rectifiers, Solar MPPT chargers, Solar trackers, Battery chargers ,Grid tie inverters design with PLL and feedback control circuit emergency light of 66W and Online UPS control cards, Battery Charging power supplies, LED drivers for PWM controlling and dimming, SMPS, Power supplies. I have experience in schematics and PCB design experience in Altium and ORCAD. I am ready to work for you. Please contact for further discussion.

Dear Sir, I am an electrical engineer with 19 years experience in this area , listed among top talented freelancers here. I am going through your requirements and will have some question. I am interested in your project ARM SOC firmware Engineer (HT5019 SoC) Please send me a private chat message.

Dear Sir, I am an embedded systems expert with more than 15 years of experience in the field of embedded systems, electronics, prototyping and PCB Layout. I have expert level skills in Cortex Mx firmware development. I have checked the details of your work and assure you the best solution for your work. Regards Ch

Hello, We are a team of talented and experienced developers and engineers. Our Solutions: Applications of Communications Equipment, Industrial & Personal Electronics, Internet of Things, Custom Designs, Software Development. Some of our skills: Embedded System, Product Prototyping, PCB and Schematic Design, Firmware Development Embedded Linux, Programming Linux System GSM, GPS/GNSS, Wifi, Bluetooth, Ethernet C/C++ Programming ARM and 8051 Microcontrollers: TI, Silicon Labs, ST, NXP etc. UART/SPI/I2C/USB/FSMC Interface and Protocol Programming Altium Designer, MATLAB, Arduino IDE, CCS, Eclipse Contact us for rapid and complete solutions. Regards UZ Solutions

hi, dear. nice to meet you. I'm Qt/C expert. I can do your job. Please discuss more details on chatting room. Regards. XiongJie C.

"Hi, Hope you are doing well! Thanks for sharing your project requirement with us. It will be our great pleasure to work on your project. I have checked your requirement, yes we can do it, because we already work on similar requirement in past. We have right skills to work on this assignment. . We will complete the work as per requirement Also my team working on same project" We have read out every thing about your project kindly confirm"

Hi. hope you are doing well. I'm an embedded software developer. I think you can realize I'm an android firmware expert via my working history. But also I have experienced in development of the firmware of network equipment. The firmware is based on linux and powerpc cpu, packet swithcing chip. I think I'm very suit for this project. I'm looking forward to hearing from you. Thanks

Hi how are you, I am an electronic engineer. I am interested in your project, I have my own studio room for product development in ShenZhen City China,I have good experienced in the circuit design, components choose, PCB design and problem analysis, and I have good sources for components purchase and manufacturer factory, In the past I was done for many Projects design that is from schematic......to final product , as like 433MHZ RF module, GPRS-DTU,power bank, videos camera, PIR LED, Audio card module, Ultrasonic water level detection,Bluetooth module, smoke detectors,cordless phone...etc, Thank you very much, and looking forward from your reply early.

I have a lot of embedded firmware development experiences,I can help you a lot on this project.I can send you some work examples later.

I am an electronic engineer from School of Engineering and Technology ITBA, and studying a Master in Embedded Systems from University of Buenos Aires, UBA. I am currently working as a freelance electronic developer I work daily designing embedded electronic equipment executing tasks such as: { Taking requirements and planning acceptance tests of hard and soft. { Schematic design, PCB, simulations, assembly, 3D modeling and machining. { Coding for real time in C / C ++ in bare metal or over RTOS. { Codification and execution of the unit tests and management of continuous integration tools. { Assembly and start-up of prototypes and assembly line documentation. I am very pragmatic, committed and enjoy solving complex problems in a creative way by exchanging ideas with my peers I prefer down-top developments using Agile concepts to keep the product functional from the beginning. I have an electronics workshop with tools such as: { Assembly line of SMD and TH plates, pasta stencil, pick and place, reflow oven and wave soldering machine. { Reworking and manual welding tools. { Stock of SMD and TH materials of current and specific use. { Machine for cutting and laser engraving. { Several machines for 3D printing. { Generators, Oscilloscopes and Advanced Instrumentation for measurement and diagnosis. These tools, my experience, technical ability and frequent academic updating allow me to unwrap in most instances of the development of a professional embedded electronic equipment.