Altium Designer Jobs

I need a PCB design expert to verify my work done in EasyEDA. Key requirements: - Check schematic accuracy and component placement. - Review and correct errors. - Simulate circuit behavior. - Check for manufacturing issues. Ideal Skills and Experience: - Proficiency in EasyEDA. - Strong understanding of PCB design principles. - Experience with error checking and simulation. - Familiarity with manufacturing processes and potential issues. Please provide a portfolio and relevant experience with similar projects.

I need a compact, production-ready PCB designed for a new consumer-grade smart-home device. The board’s core task is to handle a dedicated control-interface switch that will let users toggle the appliance on and off and cycle through a few operating modes. Space is not tight, so component selection and trace routing will be no problem. You’re free to work in Altium Designer, KiCad, or Eagle—whichever lets you move fastest while still delivering neat, well-documented files. If you choose RF-friendly parts, please keep the layout compatible PCB Easy or JLCPCB. Deliverables I expect: • Schematic and PCB layout files • Gerber, drill, and pick-and-place outputs ready for fabrication • A tidy BOM with supplier part numbers and current pricing • Assem...

I need a double-layer, signal-processing board laid out in Altium Designer and prepared for fabrication at JLCPCB. The finished board will fit inside a 15 cm × 15 cm envelope, so component placement, routing, and keep-outs should respect that medium-size constraint. Deliverables I expect: • Complete Altium project with schematics and PCB layout • Optimised Gerber, drill, and pick-and-place files matched to JLCPCB’s specs • BOM with manufacturer part numbers and assembly notes I will review the design by importing the files directly into Altium and running JLCPCB’s online DFM check; the job is complete once the files upload without errors and the board passes ERC/DRC.

I have three existing Altium Designer projects that must be refreshed before the next manufacturing run at JLCPCB. Both the schematic and the board layout need attention. On the schematic side I already know the exact edits: a handful of parts have to be added or removed, several nets must be reassigned, and a few voltage- and current-related values updated. Once those changes are in place the PCB layouts have to be brought in line—rerouting where required, keeping the original board outlines and mechanical constraints intact, and making sure every DRC/ERC check comes up clean. When the files are solid I need a full, ready-for-upload manufacturing package: • Updated Altium project files (.PrjPcb, .SchDoc, .PcbDoc) • Gerber and NC-Drill set generated with JLCPCB’s ...

We are developing a carwash kiosk control board that will work together with our Paymore TPOS device, and we are looking for an experienced embedded hardware designer to design a production-ready PCB. This is a real commercial product that will go into mass production, therefore the design must be industrial-grade and manufacturable. The board will control a P10 LED panel (HUB75) that runs continuously 24/7, displaying countdown timers and simple messages. The system must also include Pulse+ and Pulse− inputs that can operate either as dry contact inputs or opto-isolated inputs, counting pulses and triggering system actions. Based on the detected pulses, the board must activate one of 10 independent output channels that can drive 5V or 24V signals for a defined period and then autom...

Freelance Hardware Engineer – Altium PCB Design Review (Remote Access) We have an existing Pulse Converter PCB designed using Altium Designer and are looking for an experienced freelance hardware / PCB design engineer to perform a technical design review. The work will be done via remote access to our computer (AnyDesk / TeamViewer). Design files will not be shared. Detailed circuit functionality and design context will be explained after mutual agreement and confidentiality alignment. Scope of Work: Review the schematic and PCB layout in Altium Designer and identify potential design issues, risks, and improvement points, including but not limited to: Power input and regulation (wide-range DC input) Relay driver circuits Optocoupler-based pulse input circuits MCU (ESP32 or sim...

I am building a tiny GPS tracker device for my company and need an experienced PCB designer. Project Requirements: - Design schematic and PCB layout for a compact GPS tracker. - Use SIM7080G (LTE/NB-IoT with GNSS) module. - Include SIM card slot, GPS antenna connector, LiPo battery connector, and charging circuit. - Board size should be approximately 18 mm x 20 mm. Deliverables: - Complete schematic - PCB layout - Gerber files for manufacturing - Bill of Materials (BOM) - Pick and Place file (optional) Preferred Tools: KiCad, Altium Designer, or EasyEDA. Experience Required: - Experience designing IoT or GPS tracking devices - Knowledge of RF layout and antenna placement Budget: $30 – $50 (negotiable) Please share examples of previous PCB designs.

I will provide the full Proteus project (schematic, PCB, libraries). Your task is to recreate that board in Altium Designer as an exact, bit-for-bit copy—same dimensions, traces, footprints and reference designators—so the migrated file can drop-in-replace the original. Once the design lives in Altium, prepare a complete production package for JLCPCB consisting of: • Gerber set generated with Altium’s CAM outputs • Pick-and-place centroid file (CSV) referenced to the board origin JLCPCB expects • Clean BOM that matches the Altium project and includes LCSC part numbers and JLCPCB’s preferred column headings Please keep the design locked as-is; no routing or placement tweaks. Organise the schematic sheets and PCB libraries so I can add compo...

We are building a solar-powered, low-power IoT field device used outdoors in orchards. We need an experienced PCB design engineer to develop a custom PCB that integrates and reliably powers the system. Scope (PCB only): 1) Schematic + PCB layout for a low-power embedded system 2) Power design: solar charging + battery management, stable rails, protection, brownout handling, and power-path switching 3) Interfaces for MCU + peripherals (camera, GNSS, cellular modem, temp/humidity sensor, RTC/power scheduler) 4) Connector selection, ESD/weather-related protection considerations, test points, and design for manufacturability Deliverables: production-ready Gerbers, BOM, pick/place, schematic, and design files (KiCad/Altium—your preference) Nice to have: Prior experience with solar/batt...